Ford Focus MK3 "reset all adaptation" function

Share your FORScan experience with other users
MarekKu
Posts: 7
Joined: Mon Mar 18, 2019 4:40 pm
Vehicle: Ford Mondeo MK4, econetic 1.6 TDCI, 2011

Re: Ford Focus MK3 "reset all adaptation" function

Post by MarekKu » Thu May 09, 2019 2:18 pm

Just small update to my experience with learning process. I was not able to complete this process and due this I have replaced all injectors.
It seems that my injectors were in bad state, this was confirmed by Bosch diesel service. If you see error like Cylinder X Fuel Injector Offset Learning At Max Limit, it can be real issue at your injector.
I had those errors at my 3 injectors, but car was going quite well (6 l/100 km - Ford Mondeo mk4, 1.6 TDCI), only my technician told me that after start at idle, he heard small irregular idle. I recognized this only after his words, but it was really low.

There is one video at youtube about FF3 with same error and technician replace that injector.

Second experience is that after replace my consumption by computer is 4,5l/100 km, which I cannot believe. I will do longer trips and will see.

nabilultranet
Posts: 1
Joined: Thu May 30, 2019 1:03 pm
Vehicle: FORD FOCUS MK3 1.6L TDCI 115 2012

Re: Ford Focus MK3 "reset all adaptation" function

Post by nabilultranet » Sat Jun 01, 2019 9:05 am

Hello everyone, i'm new in this forum (i'm from France and own a Focus mk3 titanium 1.6L TDCI 115 2012).
First of all i want to thank the FORScan team for their great job, this scan tool is really good.
Thanks to all users who post and share their experiences and solutions in this forum.

I don't really have issues with my car, it work normaly, but since 1 to 2 mounths i fell some vibrations in cockpit and steering wheel, this happen in idle and when i accelerate.

I performed a scan and got no erreurs at all.

My question is this : can i perform a relearning injection just by following the procedure described in this post or it is obligatory to do a "reset all adaptation" or "Reset pilot injection quantity learned values" before ?

Thank you for your answers.

MarekKu
Posts: 7
Joined: Mon Mar 18, 2019 4:40 pm
Vehicle: Ford Mondeo MK4, econetic 1.6 TDCI, 2011

Re: Ford Focus MK3 "reset all adaptation" function

Post by MarekKu » Fri Jul 26, 2019 3:30 pm

If there is no error related to injectors, dont do it. You can do injector correction test via computer and physical injector leaking test.
I think if correction are around 1 it is ok.
You can monitor fuel pressure required, real, MAF pressure, if all is fine, it can be something which cannot be monitor by sensors.

FH2k
Posts: 6
Joined: Mon Jun 10, 2019 1:02 pm
Vehicle: Mazda 6 Gy, 2.3 2003

Re: Ford Focus MK3 "reset all adaptation" function

Post by FH2k » Tue Jul 30, 2019 5:23 pm

Hey there. I'm about to check out a Ford mondeo 2.5 tcdi, 2005 and need some guidance. The owner told me that he has an error regarding the injector on cylinder 1. He changed the injector, now he got a problem with the injector on cylinder 2. By any chance, is this just an error because he might didn't set new values, did a reset or something like that?

ssteell
Posts: 1
Joined: Mon May 27, 2019 6:50 pm
Vehicle: Ford 1.6 DCI C-max 2004

Re: Ford Focus MK3 "reset all adaptation" function

Post by ssteell » Thu Aug 15, 2019 6:35 am

Hello all,

I Want share my experience.
I have this error on Ford C-MAX 2011 1.6 85 kW Duratorque. Before engine works pretty fine, no smoke only bad acceleration in low RPM and some fuel leak from fuel return line. I decided to remove all injectors and check them.
I one of workshops test show (cost me 28 Eur), that 3 of 4 injectors are in very bad state, that means low fuel flow in some ranges of RPM reasoned of bad injectors electronic. I decided to buy new ones from Poland dealer. That cost me around 750 Eur with delivery costs. After I replaced injectors (I replaced all the glow plugs at the same time because 2 were bad) and coded them to engine with Forscan and do some ride in hi RPM range, all works fine, when injectors learned, and fuel consumption dropped from 5.6 to 4.4 Ltr/km. So Forscan helped me a lot.

It is unfortunate that the car's PCM does not issue errors to the driver like nozzle and plugs wear.

And I suggest - never try buy old injectors from cars with more then 50000 km run, this is waste of time and money.
And if you have error about injectors learning at high values, i do not recommended reset adaptations, because you can have engine jerking after that, because old worn injectors cannot return to normal working state.

douge6666
Posts: 8
Joined: Tue Sep 03, 2019 2:34 pm
Vehicle: Fusion,2.0t/245,2017

Re: Ford Focus MK3 "reset all adaptation" function

Post by douge6666 » Tue Sep 24, 2019 6:30 am

good :roll: :roll:

Denis
Posts: 1
Joined: Thu Sep 13, 2018 12:24 pm
Vehicle: Ford Fusion 2014

Re: Ford Focus MK3 "reset all adaptation" function

Post by Denis » Thu Oct 17, 2019 7:55 pm

Hello, does anyone know the relearn procedure for Ford Fusion 2G 2014 after 'reset all adaptations' function has been carried out?

handou8888
Posts: 9
Joined: Tue Sep 03, 2019 2:24 pm
Vehicle: Fusion, 2.0t/245, 2017

Re: Ford Focus MK3 "reset all adaptation" function

Post by handou8888 » Fri Nov 22, 2019 9:56 am

oh well

Post Reply