Page 10 of 18

Re: How to program PATS using FORScan v2.3.*

Posted: Sat Aug 04, 2018 10:47 am
by rs2k16valve
Hi all

I have got to the screen for outcode/incode only my incode begins 1040 which states have to contact them ? anyone know how to help here ?
Thanks

Re: How to program PATS using FORScan v2.3.*

Posted: Sat Aug 04, 2018 12:19 pm
by rs2k16valve
does anywhere support a calculator the the newer type incode/outcode ? All I am finding is places wanting to charge a fortune and people saying it dont work.

Re: How to program PATS using FORScan v2.3.*

Posted: Mon Aug 06, 2018 6:38 pm
by crunchie
I have a 2011 cmax with keyless start and a key like in the image attached.

I have one key that works in keyless mode and it's buttons work to unlock the car.
A 2nd key that the buttons don't work ( presumed faulty as battery has been changed) it will allow the car to start ONLY when it is inserted into the hole in the steering column.

I bought a blank key that I was hoping to program but I cannot see a PATS section anywhere in forscan!?

I have also tried th method where you turn ignition on/off multiple times until it chimes then are meant to
Press unlock.

Any ideas how I program this key?

Re: How to program PATS using FORScan v2.3.*

Posted: Tue Aug 07, 2018 10:47 am
by bajaa
hello guys,i have mazda 2 2008,and i tried to programm blank chinese key but i got error

Re: How to program PATS using FORScan v2.3.*

Posted: Wed Aug 22, 2018 4:52 am
by oaklanddriver
I have a 2005 Ford F-150 Lariat model, my truck was stolen last year because a thief found my extra key in my other car. So, i was always missing 1 key and always felt nervous about the thief coming back and taking my truck again.

I bought a blank key from ebay, had it cut from a local locksmith for $2 and was able to add a third key via FORScan following this procedure. Tomorrow i'm going to try to erase all keys and program only the ones that I have in hand. Thank you very much for this program, worked like a charm.

Re: How to program PATS using FORScan v2.3.*

Posted: Tue Aug 28, 2018 10:46 am
by rabbitgtdguy
Is there a limit to the number of keys that FORScan will allow you to program?

Joe

Re: How to program PATS using FORScan v2.3.*

Posted: Fri Aug 31, 2018 6:18 am
by Hockeyfreak
Hey all, just got a great deal on a 2013 F150 XLT 4x4. Has some problems like the 4.3 screen is out, backup camera screen shows white, SRS light on the center console is always lit (seat sensor detects a person there for seatbelt) and lastly it has one key that the dealer had made (I assume it was made as a master) but someone must've accidentally made it a restricted key with MyKey, and it's limited to 80 MPH and mutes stereo without seatbelt. There's other restrictions I'm sure. I'm just reading about this Forscan software, ordered my ScanTool 426101 OBDLink MX Bluetooth on Amazon. My question before I start going in and deleting keys and trying to load them again is will this work with my "limited' key. Will I be able to get back to having full rights keys. I bought two new keys from Ebay guaranteed to work, had them cut, and ready to go. Please let me know if I will be able to do it. I'll follow the tutorial in the opening post if so! Hopefully, Forscan can help me diagnose some of the other problems also.

Thanks!

Re: How to program PATS using FORScan v2.3.*

Posted: Mon Sep 03, 2018 9:09 pm
by Hockeyfreak
Hockeyfreak wrote:
Fri Aug 31, 2018 6:18 am
Hey all, just got a great deal on a 2013 F150 XLT 4x4. Has some problems like the 4.3 screen is out, backup camera screen shows white, SRS light on the center console is always lit (seat sensor detects a person there for seatbelt) and lastly it has one key that the dealer had made (I assume it was made as a master) but someone must've accidentally made it a restricted key with MyKey, and it's limited to 80 MPH and mutes stereo without seatbelt. There's other restrictions I'm sure. I'm just reading about this Forscan software, ordered my ScanTool 426101 OBDLink MX Bluetooth on Amazon. My question before I start going in and deleting keys and trying to load them again is will this work with my "limited' key. Will I be able to get back to having full rights keys. I bought two new keys from Ebay guaranteed to work, had them cut, and ready to go. Please let me know if I will be able to do it. I'll follow the tutorial in the opening post if so! Hopefully, Forscan can help me diagnose some of the other problems also.

Thanks!
Bump? Please?

Re: How to program PATS using FORScan v2.3.*

Posted: Thu Sep 06, 2018 12:18 am
by Exploder
I've read every post regarding programing a PATS key.
I have a 2016 Explorer Sport and when connected, I can't find any PATS on the list of any modules.
I don't see how to do the 10 min wait.

Can anyone just point me in the right direction?

Re: How to program PATS using FORScan v2.3.*

Posted: Sat Sep 29, 2018 8:23 pm
by 18sOnAiR
Exploder wrote:
Thu Sep 06, 2018 12:18 am
I've read every post regarding programing a PATS key.
I have a 2016 Explorer Sport and when connected, I can't find any PATS on the list of any modules.
I don't see how to do the 10 min wait.

Can anyone just point me in the right direction?
In the exact same boat. Same year and model 2016 Explorer Sport Using Bosch M-VCI with extended license
Tried to attach screen shot from phone after resizing down to 740kb status shows error unable to determine image diminsions