Page 3 of 3

Re: Backup camera calib error B115E:08-48

Posted: Wed Jul 04, 2018 9:22 pm
by mandrews
I'm getting ready to retrofit a cam in my 17 f150. have all the ford parts now but need the wiring diagram for the plugs from fender well to tailgate harness so i can add the wires to plug correctly anyone have a link or info?
Thanks

Re: Backup camera calib error B115E:08-48

Posted: Thu Jul 05, 2018 4:15 am
by f-wolf

Re: Backup camera calib error B115E:08-48

Posted: Fri Jun 14, 2019 11:03 pm
by DBooth
Anybody have this issue? Did the camera install thing everything works image is right side up, zoom works, dynamic lines are there and turn with the steering wheel BUT as soon as I move in reverse the lines go all the way left and stay there until I stop moving then when ove back to center. The camera is a OEM replacement from rock auto and is made by dorman. When I do the calibration I get the same error code as everybody else. Any ideas?

Re: Backup camera calib error B115E:08-48

Posted: Fri Jun 14, 2019 11:33 pm
by BBradley52
I just installed the same camera in my 2013 Fusion. I get the same results with the guidelines. I haven't tried to calibrate yet. (Waiting on interface module from Amazon but have installed Forscan software). I suspect it is because we didn't install an OEM camera. Hope not because we can't return to Rock Auto. I sent Dorman Tech Support an email, but no response. Not much hope. I think we're screwed.

Re: Backup camera calib error B115E:08-48

Posted: Sun Jun 16, 2019 4:25 pm
by BBradley52
Got ELM adapter and installed with software successfully. Ran calibration of Dorman (aftermarket camera). Calibration SAID it was run successfully. Interesting because most say that it faults at 8% of calibration run. Mine ran to around 20-30% then asked me to turn off and back on Ignition. After doing this, it ran to completion of 100% and said the calibration was successful. The only problem is the guidelines act just as before. Once you move in the reverse direction the white guidelines go to hard left and stay there regardless of wheel position until you come to straight position near stop. Again, this must mean that you MUST use OEM camera and not aftermarket regardless of the price.

Re: Backup camera calib error B115E:08-48

Posted: Mon Aug 12, 2019 6:18 pm
by denbo
I think dorman in the US are same as euro car parts in uk, cheap useless rubbish.

Re: Backup camera calib error B115E:08-48

Posted: Tue Oct 22, 2019 11:38 am
by Levowen
I had my rear camera replaced with a part from ford after an accident. But now rear guidelines are not showing. Dealer doesn’t know how to fix it. After reading this forum I bought a lead to use with FORScan. But my vehicle doesn’t have the recalibrate camera option in FORScan.

Anyone have suggestions on what to reset? The the camera is throwing a DTC that says it requires calibration.

Re: Backup camera calib error B115E:08-48

Posted: Tue Jun 09, 2020 2:55 am
by rbearden
[C:desktop/F150][/backup camera.jpg]

I am getting a little bit different issue. I installed a RAAYOO camera from Amazon in my 2016 F150 XL. I am pretty sure that I have the wiring right. White/green is positive to camera and purple/brown wire is negative. Camera is powered from the trailer light harness when I shift to reverse. I have checked the power when in reverse and have 12V. BdyCM LIN runs to 8% and then gives me a B1155E:08-0A in the DTC.

Code: B115E - Camera Mode
Additional Fault Symptom:
- Bus Signal/Message Failures

Status:
-DTC Present at Time of Request
-Malfunction Indicator Lamp is Off for the DTC

Module: Body Control Module

Any ideas or help on this issue?

Re: Backup camera calib error B115E:08-48

Posted: Tue Jun 09, 2020 5:01 am
by e1337ninja
rbearden wrote:
Tue Jun 09, 2020 2:55 am
[C:desktop/F150][/backup camera.jpg]

I am getting a little bit different issue. I installed a RAAYOO camera from Amazon in my 2016 F150 XL. I am pretty sure that I have the wiring right. White/green is positive to camera and purple/brown wire is negative. Camera is powered from the trailer light harness when I shift to reverse. I have checked the power when in reverse and have 12V. BdyCM LIN runs to 8% and then gives me a B1155E:08-0A in the DTC.

Code: B115E - Camera Mode
Additional Fault Symptom:
- Bus Signal/Message Failures

Status:
-DTC Present at Time of Request
-Malfunction Indicator Lamp is Off for the DTC

Module: Body Control Module

Any ideas or help on this issue?
It seems to be the consensus that if you are not using an actual OEM Ford Camera that you will run into this error code and there is no working fix.

Re: Backup camera calib error B115E:08-48

Posted: Sun Aug 02, 2020 2:58 pm
by LT4Ryan
I have a 2015 explorer and replaced the camera, but for some reason I don't have the service procedure to calibrate it. The generic BodyCM local internetwork connect option isn't helping either. I am on the latest version of forscan - is there something I can do to try to fix it before I take it to the dealer?