Need to reprogram rear camera

Share your FORScan experience with other users
Aymanodat
Posts: 15
Joined: Sun May 23, 2021 1:01 pm
Vehicle: Ford mondeo 2016

Re: Need to reprogram rear camera

Post by Aymanodat »

No one know how to enable the guide white line ?
Ecmbuster
Posts: 1303
Joined: Sun Mar 15, 2015 4:08 am
Vehicle: Volvo Bertone and two Motorcyles
Location: On a spinning rock

Re: Need to reprogram rear camera

Post by Ecmbuster »

Aymanodat wrote:
Sun Jun 13, 2021 8:24 pm
No one know how to enable the guide white line ?
What kind of camera, OEM camera, after-market camera.
What kind of display?
More information is required.
Do not ask for help in PM. Use the forum to ask and answer questions!
Aymanodat
Posts: 15
Joined: Sun May 23, 2021 1:01 pm
Vehicle: Ford mondeo 2016

Re: Need to reprogram rear camera

Post by Aymanodat »

Ecmbuster wrote:
Mon Jun 14, 2021 12:13 am
Aymanodat wrote:
Sun Jun 13, 2021 8:24 pm
No one know how to enable the guide white line ?
What kind of camera, OEM camera, after-market camera.
What kind of display?
More information is required.
I bought after market camera This one
https://www.amazon.co.uk/dp/B07GWLJGTL ... UTF8&psc=1

My car ford mondeo 2016 with sync 2
The camera work fine with red green and yellow fixed guidelines not white line
Ecmbuster
Posts: 1303
Joined: Sun Mar 15, 2015 4:08 am
Vehicle: Volvo Bertone and two Motorcyles
Location: On a spinning rock

Re: Need to reprogram rear camera

Post by Ecmbuster »

If you had SYNC in the car before, it should have the correct firmware.
If SYNC was installed after, that should have been mentioned first.
If the camera is after-market, follow their installation instructions and request their support first.
If the camera still fails, ask for a replacement or install OEM.
Do not ask for help in PM. Use the forum to ask and answer questions!
Aymanodat
Posts: 15
Joined: Sun May 23, 2021 1:01 pm
Vehicle: Ford mondeo 2016

Re: Need to reprogram rear camera

Post by Aymanodat »

Ecmbuster wrote:
Mon Jun 14, 2021 3:57 pm
If you had SYNC in the car before, it should have the correct firmware.
If SYNC was installed after, that should have been mentioned first.
If the camera is after-market, follow their installation instructions and request their support first.
If the camera still fails, ask for a replacement or install OEM.
The car didn’t come with reverse camera i had to buy Harness Cable with rca to connect the camera and i enabled the reverse camera through forscan
aekkaphan
Posts: 4
Joined: Mon May 31, 2021 4:03 pm
Vehicle: ford ranger2016

Re: Need to reprogram rear camera

Post by aekkaphan »

I want to activate Reverse camera distance guide line Turn along the steering wheel (dynamic) in sync2.5 and sync3

please help me
wgraggio
Posts: 2
Joined: Wed May 26, 2021 12:00 am
Vehicle: lincoln mkz 2015

Re: Need to reprogram rear camera

Post by wgraggio »

Same problem, interlink or calibration stop at 8% with new oem camera on lincoln mkz 2016, i changed my camera with the same part number.
i changed it because the older one got paint on the lens. With the new one, sometimes i see the guidelines, and most of the time, no.

I think there must be another procedure, before BCM calibration , reset or interlink .
Rolfecat
Posts: 4
Joined: Tue Oct 06, 2020 8:14 pm
Vehicle: Ford Mustang, 2.3 Ecoboost, 2016

Re: Need to reprogram rear camera

Post by Rolfecat »

Do you have the engine running?
wgraggio
Posts: 2
Joined: Wed May 26, 2021 12:00 am
Vehicle: lincoln mkz 2015

Re: Need to reprogram rear camera

Post by wgraggio »

No, FORSCAN says ignition ON but do not run engine. Why?
Rolfecat
Posts: 4
Joined: Tue Oct 06, 2020 8:14 pm
Vehicle: Ford Mustang, 2.3 Ecoboost, 2016

Re: Need to reprogram rear camera

Post by Rolfecat »

I’ve found that sometimes the engine needs to be running. Give it a try and you may find it will complete the process.
Post Reply