Technical Information on the functions on the 1.6 TDCi engin

Any issues related to FORScan application
micky83
Posts: 6
Joined: Sat Jul 05, 2014 12:28 pm
Vehicle: Ford Focus 1.6 TDCi 110cv FAP - 2009

Technical Information on the functions on the 1.6 TDCi engin

Post by micky83 » Sun Aug 17, 2014 1:55 pm

Hello FORScan Team! ;)

I own a Ford Focus 1.6 TDCi 110cv FAP (06/2009); I would like to know if it would be possible with FORSCAN, maybe in the future, reset the parameters of the adaptive module (PCM reset KAM), turn on / off the FAP/DPF (FAP-off/DPF-off switch, turn off preparation Particulate Filter) and other functions, in general, always related to this type of engine. :?:
Thanks for your cooperation. ;)
Best Regards.
Last edited by micky83 on Thu Aug 21, 2014 8:57 pm, edited 1 time in total.

FORScan
Site Admin
Posts: 2596
Joined: Fri Jun 13, 2014 2:21 am

Re: Technical Information on the functions on the 1.6 TDCi e

Post by FORScan » Wed Aug 20, 2014 9:44 am

We will be able to check & comment after 26th (end of team vacation).

Regards,
FORScan Team

bluebear
Posts: 4
Joined: Wed Aug 20, 2014 12:56 pm
Vehicle: ford focus 2 1.6 tdci 90 hp

Re: Technical Information on the functions on the 1.6 TDCi e

Post by bluebear » Wed Aug 20, 2014 1:13 pm

Hello,

Same situation here, I own a Ford Focus mk2 1.6 TDCI 90 HP (psa). It will be great to have some more functions available for modification (like in elmconfig software).
FORscan looks more greatful than the other software, is more compact (the menus).

If you need some logs from my car with Forscan or with Elmconfig i can help you for further development.

micky83
Posts: 6
Joined: Sat Jul 05, 2014 12:28 pm
Vehicle: Ford Focus 1.6 TDCi 110cv FAP - 2009

Re: Technical Information on the functions on the 1.6 TDCi e

Post by micky83 » Thu Sep 25, 2014 9:16 pm

So it's not really possible to reset the KAM to our type of engine 1.6 TDCi ( Bosch PCM ) ? :?:

FORScan
Site Admin
Posts: 2596
Joined: Fri Jun 13, 2014 2:21 am

Re: Technical Information on the functions on the 1.6 TDCi e

Post by FORScan » Tue Sep 30, 2014 10:31 am

Sorry for delay with answer.
micky83 wrote:So it's not really possible to reset the KAM to our type of engine 1.6 TDCi ( Bosch PCM ) ? :?:
This type of PCM doesn't support Reset All Adaptations function. Instead of, it is possible to reset certain subsystems. Some of these reset functions are already implemented in FORScan (DPF, DPS, EGR reset ) but some are still not (intake air throttle valve, cooling fan motor, exhaust gas temperature sensort etc).
micky83 wrote:turn on / off the FAP/DPF
Not sure what you mean under turn on/off, if you are talking about disabling DPF (DPF removal), then it is not a service function but rather ECU reprogramming, this is not implemented yet.

mx-user
Posts: 18
Joined: Sun Jun 22, 2014 1:33 pm

Re: Technical Information on the functions on the 1.6 TDCi e

Post by mx-user » Thu Jan 01, 2015 1:57 pm

Hi, I also own a 1.6 TDCI.
Service Procedure in new software update have new procedures, named (in german language)
-Additivbehällter Nachfüllen
-Additiv entlüften

Am I right that
-Additivbehällter Nachfüllen set a counter Additiv container is full; in this way or in a similar way
-Additiv entlüften must only used if the Additiv container was complete empty? (What do this procedue? Start the additive pump for some seconds? How often should execute the procedure?)

Best regards (and a happy New Year)

EDIT: Sorry, I have a 1.6 TDCI built in 2006. If topic does not apply, please shift it to an applicable place. Thx
Maybe "Mazda3 Y6 2003-2008 new service functions" is similar.

FORScan
Site Admin
Posts: 2596
Joined: Fri Jun 13, 2014 2:21 am

Re: Technical Information on the functions on the 1.6 TDCi e

Post by FORScan » Fri Jan 02, 2015 2:54 am

Kraftstoffadditivbehälter nachfüllen (Refill the Fuel Additive Tank) - carried out if the Fuel Additive Tank is refilled.
Kraftstoffadditiv Systementlüftung (Fuel Additive System Prime) - carried out if the Fuel Additive Tank is replaced or if any of the pipes are disconnected

From diagnostic tester point' of view, both functions are quote simple and similar - tester makes counters reset and initializes FACM configuration with new data. Tester doesn't activate any actuators, such as additive pump. Everything the rest should be performed by modules.

mx-user
Posts: 18
Joined: Sun Jun 22, 2014 1:33 pm

Re: Technical Information on the functions on the 1.6 TDCi e

Post by mx-user » Sun May 03, 2015 7:01 am

For the Mazda 3 I've read, a possible cause for the DTC 2458 is
"Scheduled maintenance does not have followed"

Anybody know how to set a 1.6 TDCI to "Scheduled maintenance done" or something like that?
Attachments
2458.compressed.pdf
DTC 2458
(79.35 KiB) Downloaded 319 times

FORScan
Site Admin
Posts: 2596
Joined: Fri Jun 13, 2014 2:21 am

Re: Technical Information on the functions on the 1.6 TDCi e

Post by FORScan » Tue May 05, 2015 2:10 pm

As far as we know, Mazda with Y6 engine has the same engine and PCM as Focus Mk2 DV6. We are not sure about maintenance, as far as we know the only maintenance available is the FAT refill.

Btw, P2458 DTC for DV6 is discussed here:

http://forscan.org/forum/viewtopic.php?f=6&t=247

micky83
Posts: 6
Joined: Sat Jul 05, 2014 12:28 pm
Vehicle: Ford Focus 1.6 TDCi 110cv FAP - 2009

Re: Technical Information on the functions on the 1.6 TDCi e

Post by micky83 » Wed Sep 02, 2015 11:14 am

Dear FORScan Team ,
yet there are no developments to make a parameter reset adaptive engine 1.6 tdci ?
At the moment there is only reset the adaptive values ​​related to EGR valve .

Post Reply