Page 14 of 15

Re: Support of J2534 (Pass-Thru) adapters in FORScan v2.2.*

Posted: Thu Oct 08, 2020 6:38 pm
by Ford_Tech
I too have the VCM2 and cannot use it due to the firmware difference between bosch’s latest firmware and Ford’s integrated diagnostic software(IDS). After I downloaded bosch’s latest firmware from their website,I wasn’t able to use IDS anymore until I backdated the firmware to the version that IDS is programmed to use. I’ve also got a USB-Link™ 2: Bluetooth Edition, Autoenginuity SP03, IC4COM, & Nav-Link that I’ve yet to try. Does anybody know if any of these others work with Forscan?

Re: Support of J2534 (Pass-Thru) adapters in FORScan v2.2.*

Posted: Sat Oct 17, 2020 11:29 am
by JNEDBM
Hi all,

I'm using a PEAK PCAN-USB adapter with up-to-date passthru driver. Can high and low are connected to HS can bus of Ford Mondeo 2001+.

J2534 adapter is found in ForScan (Adapter: PCANPT32) but it does not connect to vehicle (no communication, check that ignition is on).

Any ideas how to get that working?

Best regards!

Re: Support of J2534 (Pass-Thru) adapters in FORScan v2.2.*

Posted: Wed Oct 21, 2020 6:24 am
by bijulal37
I have cardaq plus 2, that works excellent.Thanks for software creators.

Re: Support of J2534 (Pass-Thru) adapters in FORScan v2.2.*

Posted: Fri Dec 04, 2020 6:22 pm
by Csubakka
Hi,

Anybody has tried genuine VAS 5054A with FORScan?

Re: Support of J2534 (Pass-Thru) adapters in FORScan v2.2.*

Posted: Mon Jan 04, 2021 1:23 am
by amr1999
Hi i have jdiag elite pro support j2534-1 and j2534-2 but it cant read ms-can ecu any idea to solve it and thank you

Re: Support of J2534 (Pass-Thru) adapters in FORScan v2.2.*

Posted: Mon Jan 04, 2021 10:45 am
by achiko0077
Which OBD port would you recommend?

Re: Support of J2534 (Pass-Thru) adapters in FORScan v2.2.*

Posted: Sun Jan 24, 2021 11:07 am
by V3lmu
Hello!

I have a genuine AVDI diagnostic device https://abrites.com/en/products/avdi

I tried to use an AVDI device and FORScan software Ford Mondeo MY03. I selected AVDI as the device that was in the menu, but the program did not recognize the car. What did I do wrong? Can't I get in my car with this device & software? :cry:

EDIT 26.1:

I bought an J1850 adapter for AVDI and also tried to connect to the car with this one. I checked the settings again.
https://ibb.co/R6p2S8z

The program finds the car, but ... no connection is found.
https://ibb.co/RTsLrxZ

If I press the button yes

Code: Select all

(OK) [20:35:37.403] Connection to adapter has been established: J2534 AVDI-PT XXXXXX
(OK) [20:35:37.404] Adapter:  AVDI-PT XXXXXX
(OK) [20:36:53.781] Connection to vehicle has been established
(OK) [20:36:53.801] Vehicle: Ford Mondeo DURATEC-HE / I4 1.8L 2001 MY
(OK) [20:36:55.632] Found module:  OBDII - On Board Diagnostic II
(OK) [20:36:57.514] Found module:  PCM - Powertrain Control Module
(ERR) [20:36:58.772] PCM: Unable to read DTC
(OK) [20:36:58.776] Found module:  IC - Instrument Cluster
(ERR) [20:37:00.606] IC: Unable to read DTC
(OK) [20:37:03.051] Found module:  RCM - Restraint Control Module
(ERR) [20:37:04.274] RCM: Unable to read DTC
(OK) [20:37:04.278] Found module:  GEM - Generic Electronic Module
(ERR) [20:37:05.499] GEM: Unable to read DTC
(OK) [20:37:07.947] Found module:  ABS - Antilock braking system
(ERR) [20:37:09.169] ABS: Unable to read DTC
If I press the button no:
https://ibb.co/fpGpGH6

Re: Support of J2534 (Pass-Thru) adapters in FORScan v2.2.*

Posted: Tue Jan 26, 2021 8:31 pm
by V3lmu
V3lmu wrote:
Sun Jan 24, 2021 11:07 am
Hello!

I have a genuine AVDI diagnostic device https://abrites.com/en/products/avdi

I tried to use an AVDI device and FORScan software Ford Mondeo MY03. I selected AVDI as the device that was in the menu, but the program did not recognize the car. What did I do wrong? Can't I get in my car with this device & software? :cry:

EDIT 26.1:

I bought an J1850 adapter for AVDI and also tried to connect to the car with this one. I checked the settings again.
https://ibb.co/R6p2S8z

The program finds the car, but ... no connection is found.
https://ibb.co/RTsLrxZ

If I press the button yes

Code: Select all

(OK) [20:35:37.403] Connection to adapter has been established: J2534 AVDI-PT XXXXXX
(OK) [20:35:37.404] Adapter:  AVDI-PT XXXXXX
(OK) [20:36:53.781] Connection to vehicle has been established
(OK) [20:36:53.801] Vehicle: Ford Mondeo DURATEC-HE / I4 1.8L 2001 MY
(OK) [20:36:55.632] Found module:  OBDII - On Board Diagnostic II
(OK) [20:36:57.514] Found module:  PCM - Powertrain Control Module
(ERR) [20:36:58.772] PCM: Unable to read DTC
(OK) [20:36:58.776] Found module:  IC - Instrument Cluster
(ERR) [20:37:00.606] IC: Unable to read DTC
(OK) [20:37:03.051] Found module:  RCM - Restraint Control Module
(ERR) [20:37:04.274] RCM: Unable to read DTC
(OK) [20:37:04.278] Found module:  GEM - Generic Electronic Module
(ERR) [20:37:05.499] GEM: Unable to read DTC
(OK) [20:37:07.947] Found module:  ABS - Antilock braking system
(ERR) [20:37:09.169] ABS: Unable to read DTC
If I press the button no:
https://ibb.co/fpGpGH6
Would there be a solution to my problem?

Re: Support of J2534 (Pass-Thru) adapters in FORScan v2.2.*

Posted: Wed Mar 03, 2021 8:32 pm
by Ecmbuster
In response to some posts about the VAS5054A
It is a J2534-1 device and can not access the Medium Speed Network
Specifications:
K line (ISO9141-2)
High-speed CAN (ISO 11898-2)
Low-speed CAN (ISO 11898-3)
J1850 (SAE J1850)
UDS Protocol
PWM Protocol

Re: Support of J2534 (Pass-Thru) adapters in FORScan v2.2.*

Posted: Mon May 03, 2021 12:59 am
by Ecmbuster
A recent test with the new Ford VCM 3 and setting it as a Pass-Thru device worked out quite well.
FORScan and the device will connect via USB and WiFi.
001.JPG
001.JPG (81.92 KiB) Viewed 1294 times
002.JPG
002.JPG (118.28 KiB) Viewed 1294 times
003.JPG
003.JPG (194.61 KiB) Viewed 1294 times
004.jpg
004.jpg (310.76 KiB) Viewed 348 times
005.JPG
005.JPG (124.91 KiB) Viewed 1294 times