Ford As Built Data Deciphering

Car configuration discussions and experience sharing
tishandian0416
Posts: 9
Joined: Thu Jan 18, 2018 1:33 am
Vehicle: 2013 Taurus Limited 3.5

Re: Ford As Built Data Deciphering

Post by tishandian0416 » Tue Feb 06, 2018 1:40 am

I have tried to change the compass to nav in the ipc it when I changed F to B it took compass away put it back to F and compass came back how do I change compass to nav

tishandian0416
Posts: 9
Joined: Thu Jan 18, 2018 1:33 am
Vehicle: 2013 Taurus Limited 3.5

Re: Ford As Built Data Deciphering

Post by tishandian0416 » Fri Feb 09, 2018 3:27 pm

Ok need some help i was trying to turn engine hours on and I used the code provided few pages back and it did not work but now when I start the car with the key after I put it in drive and now it says on the left side ipc no key detected ... Any help please

FiveLeeter918
Posts: 25
Joined: Wed Nov 01, 2017 5:26 pm
Vehicle: 2013 Ford Taurus SHO
Location: Tulsa, OK
Contact:

Re: Ford As Built Data Deciphering

Post by FiveLeeter918 » Fri Feb 09, 2018 3:58 pm

What vehicle? Are you sure you changed the correct module?
- Lee

2013 Taurus SHO PP
AWD gauge, EQ presets, Nav in Motion, Double Honk Deactivated, Signal Flash increased to 5, Engine hours enabled, DRLs enabled

tishandian0416
Posts: 9
Joined: Thu Jan 18, 2018 1:33 am
Vehicle: 2013 Taurus Limited 3.5

Re: Ford As Built Data Deciphering

Post by tishandian0416 » Fri Feb 09, 2018 7:06 pm

2013 taurus limited with turn key ignition I used ipc block number 720-01-02 changed last number in block 3 to a 3 to try and enable engine hours this did not work but said write successful also did the nav in ipc that worked I can provide more info if needed
download/file.php?id=2554
Used this image

ClockWorK
Posts: 116
Joined: Sat Mar 05, 2016 11:29 pm
Vehicle: 2013 Taurus SHO pp
Location: Detroit Area
Contact:

Re: Ford As Built Data Deciphering

Post by ClockWorK » Fri Feb 09, 2018 8:11 pm

For engine hours, where are you looking in the IPC? It's surprisingly hard to find. it's under Information, System Check, then scroll to the bottom.

I also recommend changing the tap-blinker from 3 blinks to 4 or 5 (personal preference obviously).
2013 Taurus SHO (pp), AWD Gauge Enabled, Engine Hours Enabled, Nav Enabled in APIM and IPC, DRLs Enabled
AsBuilt Compare Tool: http://www.compulsivecode.com/Project_A ... mpare.aspx

tishandian0416
Posts: 9
Joined: Thu Jan 18, 2018 1:33 am
Vehicle: 2013 Taurus Limited 3.5

Re: Ford As Built Data Deciphering

Post by tishandian0416 » Fri Feb 09, 2018 10:01 pm

Ok this is werid I think my car thinks it has push button start it says push break to start and acc. power active I have not seen this before changed 4 to a 8 in block 1 tried reverting back and nothing ### update changed the 4 in block 1 of 720-01-02 back to a F still the same I don't remember changing anything else what can I do
Attachments
1518214200562712817235.jpg
1518214200562712817235.jpg (136.18 KiB) Viewed 3575 times
15182141628522007338952.jpg
15182141628522007338952.jpg (146.96 KiB) Viewed 3575 times

AmigaSurfer
Posts: 15
Joined: Tue Apr 05, 2016 9:31 pm
Vehicle: Mondeo MK5 1.6l Ecoboost

Re: Ford As Built Data Deciphering

Post by AmigaSurfer » Sat Feb 10, 2018 10:06 am

Why you don't make an backup before changing anything?!
Your original As Built data can you download here https://www.motorcraftservice.com/AsBuilt.

tishandian0416
Posts: 9
Joined: Thu Jan 18, 2018 1:33 am
Vehicle: 2013 Taurus Limited 3.5

Re: Ford As Built Data Deciphering

Post by tishandian0416 » Sun Feb 11, 2018 1:07 am

ok I think I figured it out the nav in ipc was causing the issue when changing the code back to factory it went away and when I changed it to nav it came back I guess this nav option is for push button start is there any other code for they key models any info on this will be helpful thanks

oslowek
Posts: 18
Joined: Sun Oct 02, 2016 7:07 pm
Vehicle: fiesta mk7 2012 1,0 100KM / mondeo mk5 2015 150KM

Re: Ford As Built Data Deciphering

Post by oslowek » Thu Feb 15, 2018 10:40 am

Hi,
Because my car is without navi and rear camera, I want to activate both systems in my mondeo (SONY Sync 2).
Could you informed me which parameters should I change? Ford navi SDCard and rear camera with wirings I will buy, of course.

Navigation activation is only in IPC 720-05-01? My settings: C028 0000 0015. Or in APIM 7D0-01-02? My settings: 001E 0806 C0C6

Camera activation is only in APIM 7D0-01-01? My settings: 086F 0582 330A

Best regards
Ondraszek

tishandian0416
Posts: 9
Joined: Thu Jan 18, 2018 1:33 am
Vehicle: 2013 Taurus Limited 3.5

Re: Ford As Built Data Deciphering

Post by tishandian0416 » Fri Feb 16, 2018 1:32 am

Follow this video for navigation in Apim this worked for me
https://youtu.be/KXZgSOOu87I
This may help you with the camera
https://youtu.be/DMpCD_f669o

Post Reply