Testing firmware update function for Ford modules

Testing new functions
robertos53
Posts: 2
Joined: Sat Jan 25, 2020 9:51 pm
Vehicle: Mondeo 2.0TDCI 180 2017

Re: Testing firmware update function for Ford modules

Post by robertos53 » Wed Dec 02, 2020 1:30 am

JUNIOR AERRE wrote:
Wed Mar 28, 2018 12:51 am
pm

litian520
Posts: 6
Joined: Tue Sep 03, 2019 5:23 pm
Vehicle: EcoBoost2.0T/204ps

Re: Testing firmware update function for Ford modules

Post by litian520 » Thu Dec 03, 2020 12:08 pm

Sent PM to Forscan team. Thanks

Sikdidit
Posts: 1
Joined: Mon Nov 30, 2020 4:15 am
Vehicle: Ford F150 2003 lariat

Re: Testing firmware update function for Ford modules

Post by Sikdidit » Thu Dec 03, 2020 6:17 pm

Sent PM to Forscan team.

User avatar
LaForge
Posts: 77
Joined: Thu Jan 19, 2017 7:42 am
Vehicle: Ford Focus 2011 - Frostwhite LaForge Edition
Location: Germany
Contact:

Re: Testing firmware update function for Ford modules

Post by LaForge » Fri Dec 04, 2020 3:28 pm

tempeldude wrote:
Thu Nov 26, 2020 8:19 am
I replaced the IPC for a UK one.
hardware and software are the same as original EU.
But the scale is not correct, could this be remedied by changing the calibration of an EU IPC?
Or should I perform a complete update?
Hmmm....

If the scale is not correct you may have done the following:

1. its a wrong ipc (like ST or RS one - they can reach 280kph instaed of 260)
2. its the wrong car. Kuga IPC does not work correctly as focus ipc. You have to search for the correct software from your car and reflash the whole ipc

I have had the same, but killing the old gb kuga software (miles were fixed and couldnt be changed to km) and reflash with actual focus soft all went fine. Now there were km and the scale was correct.

Try it.

best regards

Karsten
riding da White Beast :lol:

ECU Programming Service on Ford Vehicles after 2006

Hugdon
Posts: 3
Joined: Tue Jun 12, 2018 3:12 pm
Vehicle: Mondeo MK5, 2.0l Duratorq 150hp,2016

Re: Testing firmware update function for Ford modules

Post by Hugdon » Wed Dec 09, 2020 10:25 pm

fordsmax471 wrote:
Thu Nov 19, 2020 8:03 am

safe ;)
JS7T-14C026-AJB
JS7T-14C026-BJB
JS7T-14C088-AJB
JS7T-14C088-BJB
- Firmware Build Date: October 30, 2017
Can you tell me the correct setting to update an 2017 GS7T IPC to JS7T? Maybe a Screenshot? And did you flash all four files in one run?

Thx!

antani
Posts: 9
Joined: Thu May 14, 2020 1:09 pm
Vehicle: Focus RS mk3

Re: Testing firmware update function for Ford modules

Post by antani » Tue Dec 15, 2020 9:01 pm

Hi!

I've flashed the AWD, IPC and BdyCM modules for my Focus RS MK3, all went well during the flashing but only when driving the car I've realized that the drive mode can't be changed as there are none when I press the hardware button on the central console.

Any idea on how I could solve that issue please?

User avatar
LaForge
Posts: 77
Joined: Thu Jan 19, 2017 7:42 am
Vehicle: Ford Focus 2011 - Frostwhite LaForge Edition
Location: Germany
Contact:

Re: Testing firmware update function for Ford modules

Post by LaForge » Wed Jan 13, 2021 12:02 pm

I am afraid, that you may have used a wrong version of Firmware.
So for example a 1.6l TIVCT Engine BCM Software will not fit all requirements a RS engine want to have to.
First you have to turn back to original state.
Then Check the Firmware Name. A firmware BV6T-14XXX-AE can be replaced by XXX-AG or AH etc.
But NEVER by a XXX-BF or greater (i.e. GH etc)
Was the version suggested by forscan?
You used the official last release of forscan?
Forscan 2,40 offered me a AM Version instead my AC. Russian forums told about an AY Version.
But Forscan 2.43 told me to use AE for my BCM Module. After going back from AY to AE all went fine again.
I guessed with AY my Power Steering was not working properly.
So back to AE and all is fine.
After going back to old version try one module after each one and check the result.

I hope it works

best regards

Karsten
riding da White Beast :lol:

ECU Programming Service on Ford Vehicles after 2006

metroplex
Posts: 11
Joined: Sat Aug 13, 2016 8:42 pm
Vehicle: Taurus, 3.5L EcoBoost, 2014

Re: Testing firmware update function for Ford modules

Post by metroplex » Wed Jan 13, 2021 12:33 pm

What devices are you using to flash the modules? Forscan said my obdlink mx wasn't good enough.

typack
Posts: 6
Joined: Wed Oct 21, 2020 3:49 pm
Vehicle: Экобуст 1.5 ff3

Re: Testing firmware update function for Ford modules

Post by typack » Mon Jan 18, 2021 1:50 pm

metroplex wrote:
Wed Jan 13, 2021 12:33 pm
What devices are you using to flash the modules? Forscan said my obdlink mx wasn't good enough.
els27 v4 from els27.ru

Post Reply