Search found 138 matches

by Juice
Sat Feb 22, 2020 2:42 pm
Forum: Configuration and Programming
Topic: TPMS help! Indicator won't go off after programming
Replies: 4
Views: 255

Re: TPMS help! Indicator won't go off after programming

!!! Always save asbuilt before modifying !!!
Have you tried fliping the switch to 1 and see if tpms works?

There is also the instrument cluster. You may be able to turn off the light there.
by Juice
Thu Feb 20, 2020 10:43 pm
Forum: Configuration and Programming
Topic: New here, but I messed it up and need your help!...
Replies: 6
Views: 537

Re: New here, but I messed it up and need your help!...

If I read the first post correctly, you made a change to the IPC aka Instrument cluster. And now you have warning lights for systems you don't have on the car. If that is so: Those fault codes are there because the cluster is looking for systems/modules you don't have. So you need to 'undo' what cha...
by Juice
Fri Feb 14, 2020 4:35 pm
Forum: Configuration and Programming
Topic: Enabling tpmsl
Replies: 2
Views: 197

Re: Enabling tpmsl

Possible, yes. But you will need sensors in the wheels installed. And then the module will need to sensors synced.
by Juice
Mon Jan 27, 2020 3:18 pm
Forum: Configuration and Programming
Topic: fog lights
Replies: 6
Views: 382

Re: fog lights

You need to enable fog lights in the controller. Select module programming. You can have two options:as-built or just module proogramming. IF you have the non as-built option, you should be able to just enable. As-built option, you will need to find out which "bit" is foglights. Find an as built fil...
by Juice
Fri Jan 24, 2020 3:28 pm
Forum: Configuration and Programming
Topic: Turn signal hyperflash
Replies: 2
Views: 323

Re: Turn signal hyperflash

Since the setting change did fix hypeerflash with lights off, I think you have another issue. I would try turning the bulbs 180* in the sockets. The issue to me sounds like a ground circuit problem. You may also need different LED bulbs. Some have separate LEDs for park and brake lights, some use ci...
by Juice
Wed Jan 22, 2020 8:34 pm
Forum: Configuration and Programming
Topic: New Brake control Module
Replies: 4
Views: 433

Re: New Brake control Module

I have an older ford truck and I added a brake controller myself. I could not just plug in and enable the factory controller. There was atleast one circuit that was not on my truck. I had to run the 12v feed for the electric brakes to the round connector for the trailer. You may or may not have all ...
by Juice
Fri Jan 10, 2020 9:00 pm
Forum: Configuration and Programming
Topic: Bcm replacement
Replies: 2
Views: 172

Re: Bcm replacement

When I programmed my old keys to the new PCM/instrument cluster (that is the PATS module in my car) I did the following: 1 PATS initialization. This step syncs the PCM and PATS (your new BCM), and delete any stored keys. 2 PATS key programming, and followed prompts by Forscan. Had to wait for the 10...
by Juice
Fri Jan 10, 2020 7:24 pm
Forum: Configuration and Programming
Topic: Configuration of Instrument Cluster
Replies: 2
Views: 292

Re: Configuration of Instrument Cluster

Possibly. I had a similiar situation with my mustang. I was able to turn off the abs and traction control lights. But, those were on because my car does NOT have ABS. And the swap cluster came from a car that did have it. You can definitely read trouble codes with Forscan and figure out why the ligh...
by Juice
Wed Jan 08, 2020 11:31 am
Forum: Configuration and Programming
Topic: 2009 Lincoln MKS speed sensor
Replies: 1
Views: 48

Re: 2009 Lincoln MKS speed sensor

It would be easier to tell her not to tailgate.
by Juice
Fri Jan 03, 2020 8:31 pm
Forum: Configuration and Programming
Topic: 2011 F150 5.0 SC new PCM
Replies: 17
Views: 575

Re: 2011 F150 5.0 SC new PCM

I have done the PATS programming on my mustang. You have to perform an initialization before you can program the keys. You said you have 2 new keys. Why? There should be no reason you couldnt use your old keys. You may need to delete any existing keys to program new ones, even if you are reusing the...