Search found 520 matches

by Andyfocus
Thu Nov 29, 2018 3:40 am
Forum: General and Support forum
Topic: Please help
Replies: 3
Views: 548

Re: Please help

put the drivers for elm in the device ur using with forscan , try the disk that came with it or goto the elm site and download them.
by Andyfocus
Wed Nov 28, 2018 8:52 pm
Forum: Configuration and Programming
Topic: 911 Assist not operational
Replies: 3
Views: 993

Re: 911 Assist not operational

check out the rcm its controls it.
can turn it on and off in rcm config
by Andyfocus
Tue Nov 27, 2018 10:20 pm
Forum: Configuration and Programming
Topic: 2006 Ford Fiesta MK6 programming 2nd hand key
Replies: 2
Views: 538

Re: 2006 Ford Fiesta MK6 programming 2nd hand key

will require wipe all keys as u only have 1 of the 2 needed,
check the how to check a key with pats topic.
by Andyfocus
Tue Nov 27, 2018 10:18 pm
Forum: Configuration and Programming
Topic: How to program Central Configuration using FORScan
Replies: 158
Views: 313283

Re: How to program Central Configuration using FORScan

works fine with mine , fails occasionially but usually completes on 2nd try , ford focus 2017 1l ecoboot <- not a typo
by Andyfocus
Tue Nov 27, 2018 9:58 pm
Forum: Diagnostics and Maintenance using FORScan
Topic: DTC U2100 "Initial configuration not complete" - module reset?
Replies: 7
Views: 6061

Re: DTC U2100 "Initial configuration not complete" - module reset?

it may be worth disconnecting the battery and shorting the + and - leads together for 10 secounds than reconnecting and run a relearn on the pcm think that error went after finding a semi decent bios file and editing it a bit . it seems to just be a general fault code but it applies to all modules ,...
by Andyfocus
Tue Nov 27, 2018 6:57 pm
Forum: General and Support forum
Topic: problem error codes
Replies: 3
Views: 637

Re: problem error codes

go get your as built data and flash with that,
changing pcm may cause immobiliser problems unless you have access to the pats system on your car.
by Andyfocus
Tue Nov 27, 2018 12:43 pm
Forum: Adapters & Connection
Topic: Modules
Replies: 2
Views: 617

Re: Modules

goto options and set the hs/ms swtich to ask to switch from auto
by Andyfocus
Tue Nov 27, 2018 11:02 am
Forum: General and Support forum
Topic: problem error codes
Replies: 3
Views: 637

Re: problem error codes

P0380 DTC Glow Plug/Heater Circuit "A" Malfunction Potential causes for this DTC may include: Fault in glow plug wiring (open, short to ground, etc.) Glow plug faulty Open fuse Faulty glow plug relay Faulty glow plug module P1187-68 could require pcm rewrite with ids to fix , Possible causes Faulty ...
by Andyfocus
Mon Nov 26, 2018 10:50 pm
Forum: Diagnostics and Maintenance using FORScan
Topic: DTC U2100 "Initial configuration not complete" - module reset?
Replies: 7
Views: 6061

Re: DTC U2100 "Initial configuration not complete" - module reset?

i wouldnt reset any module ( but if you do its the bcm ) forscan will tell you where the error is coming from(module ), i would first find out why the stop start isnt working as it incomplete and not "not compatable" or "error", thier should also be some numbers after the U2100 this will explain in ...
by Andyfocus
Tue Nov 20, 2018 8:02 pm
Forum: Configuration and Programming
Topic: P1635 in TCM or PCM after tire size change
Replies: 25
Views: 15184

Re: P1635 in TCM or PCM after tire size change

when doing anything like this on cars after 2015 , write BCM module then on same window should have write to other secoundary module , do that as well ( should write same to ipc ), then turn ignition off for 30 secounds , then turn on and use relearn on pcm if required , but leaving ignition off sho...