Search found 33 matches

by Donny
Sat Jul 14, 2018 8:55 pm
Forum: Diagnostics and Maintenance using FORScan
Topic: help reading dp dpf log
Replies: 1
Views: 554

Re: help reading dp dpf log

If the reading you get with the ignition on but not running is near 0, then 1.2 is quite high. If the DPF is in very good condition the difference should be not much more than 0.2 at idle. There is an excellent post by Sinclair on this forum that should tell you all you need to know. Here is a link ...
by Donny
Fri Jul 13, 2018 8:52 pm
Forum: Diagnostics and Maintenance using FORScan
Topic: Transit T350 2.4TDCI 103kw AWD 2010 doesn't fire up, no fault codes.
Replies: 6
Views: 2802

Re: Transit T350 2.4TDCI 103kw AWD 2010 doesn't fire up, no fault codes.

I don't know what your figures should be but you are unlikely to see FRP figures of over 1000 Bar with the Van stationary, even if you rev it hard. With the vehicle moving under load the pressure can go over 1500 Bar under acceleration. I think your problem is an air starvation one. If your engine h...
by Donny
Sat Jun 16, 2018 9:28 pm
Forum: Diagnostics and Maintenance using FORScan
Topic: Strange issue
Replies: 8
Views: 21624

Re: Strange issue

Deamon444, 32780 KPa = 327.8 Bar, which looks right for Idle Pressure. I don't have the same car as you but my Idle Pressure is around 300 Bar. I haven't tried this in the laptop version of FORScan, but in the Mobile Phone version you can change the units to show the values in Bar by clicking onto it.
by Donny
Sun May 06, 2018 8:50 am
Forum: Diagnostics and Maintenance using FORScan
Topic: EGR/Pressure/Injector ? (P2458 Mazda 3 Y6)
Replies: 12
Views: 5422

Re: EGR Problem/Pressure/.. ? (P2458)

Just to clarify Hallex, the EGR_TV that I was writing about is not part of the EGR Valve. It is situated on the opposite side of the engine between the large rubber intercooler hose and the inlet manifold. The EGRVP that goes to 0 in your screenshots is part of the EGR Valve. If the EGR_TV is sticki...
by Donny
Fri May 04, 2018 7:12 pm
Forum: Diagnostics and Maintenance using FORScan
Topic: EGR/Pressure/Injector ? (P2458 Mazda 3 Y6)
Replies: 12
Views: 5422

Re: EGR Problem/Pressure/.. ? (P2458)

Hallex, I'm not an expert, I don't have the same engine as you but the EGR_TV values do not make sense. In my later model Focus this value is for the Air Shut Off Valve (Anti Shudder Valve )(Throttle Valve) in the Inlet Manifold. My later car does not have Eolys additive so what I'm writing might no...
by Donny
Thu Jan 04, 2018 9:57 pm
Forum: General and Support forum
Topic: Forscan light and new OBDLink MX
Replies: 3
Views: 1581

Re: Forscan light and new OBDLink MX

I have only needed to accept the pairing code the first time I connected to my phone, after a phone factory reset and when I got a new phone. Every other time it connects automatically. The manufacturers of OBDLink have a forum as well, you could have a search through there or ask them the same ques...
by Donny
Wed Jan 03, 2018 9:39 pm
Forum: General and Support forum
Topic: Forscan light and new OBDLink MX
Replies: 3
Views: 1581

Re: Forscan light and new OBDLink MX

It works ok on my Android phone.

You need to follow the pairing instructions that came with OBDLink MX, but before you do that open the settings in the FORScan App and try setting the Connection type to Bluetooth 0, if that does not work you could try Bluetooth 1 or 2.
by Donny
Tue Dec 19, 2017 9:24 pm
Forum: Diagnostics and Maintenance using FORScan
Topic: Engine malfunction
Replies: 3
Views: 1622

Re: Engine malfunction

Try this procedure, it works with a lot of Ford Cars.

Get in car and close all doors
Turn Ignition on, but do not start
Press the Brake pedal and the Accelerator pedal at the same time and keep them pressed for about 20 seconds

The light should now go off.
by Donny
Sun Nov 05, 2017 9:45 pm
Forum: Diagnostics and Maintenance using FORScan
Topic: DP_DPF values
Replies: 13
Views: 13195

Re: DP_DPF values

I have the same car as you and the values I get are about the same as yours.
by Donny
Tue Jul 25, 2017 9:27 pm
Forum: Diagnostics and Maintenance using FORScan
Topic: Fault codes P0807:00-2F AND P0806:00-2F
Replies: 1
Views: 5528

Re: Fault codes P0807:00-2F AND P0806:00-2F

I have the previous model (mark 2 Focus) but without cruise control and I had to replace my clutch position sensor. It was located at the end of the clutch pedal near the pivot point in the drivers footwell and is a simple plunger. In my case it looked ok but the spring inside it was broken so the e...