Search found 125 matches

by Juice
Mon Jan 27, 2020 3:18 pm
Forum: Configuration and Programming
Topic: fog lights
Replies: 1
Views: 39

Re: fog lights

You need to enable fog lights in the controller. Select module programming. You can have two options:as-built or just module proogramming. IF you have the non as-built option, you should be able to just enable. As-built option, you will need to find out which "bit" is foglights. Find an as built fil...
by Juice
Fri Jan 24, 2020 3:28 pm
Forum: Configuration and Programming
Topic: Turn signal hyperflash
Replies: 2
Views: 195

Re: Turn signal hyperflash

Since the setting change did fix hypeerflash with lights off, I think you have another issue. I would try turning the bulbs 180* in the sockets. The issue to me sounds like a ground circuit problem. You may also need different LED bulbs. Some have separate LEDs for park and brake lights, some use ci...
by Juice
Wed Jan 22, 2020 8:34 pm
Forum: Configuration and Programming
Topic: New Brake control Module
Replies: 3
Views: 309

Re: New Brake control Module

I have an older ford truck and I added a brake controller myself. I could not just plug in and enable the factory controller. There was atleast one circuit that was not on my truck. I had to run the 12v feed for the electric brakes to the round connector for the trailer. You may or may not have all ...
by Juice
Fri Jan 10, 2020 9:00 pm
Forum: Configuration and Programming
Topic: Bcm replacement
Replies: 2
Views: 120

Re: Bcm replacement

When I programmed my old keys to the new PCM/instrument cluster (that is the PATS module in my car) I did the following: 1 PATS initialization. This step syncs the PCM and PATS (your new BCM), and delete any stored keys. 2 PATS key programming, and followed prompts by Forscan. Had to wait for the 10...
by Juice
Fri Jan 10, 2020 7:24 pm
Forum: Configuration and Programming
Topic: Configuration of Instrument Cluster
Replies: 2
Views: 203

Re: Configuration of Instrument Cluster

Possibly. I had a similiar situation with my mustang. I was able to turn off the abs and traction control lights. But, those were on because my car does NOT have ABS. And the swap cluster came from a car that did have it. You can definitely read trouble codes with Forscan and figure out why the ligh...
by Juice
Wed Jan 08, 2020 11:31 am
Forum: Configuration and Programming
Topic: 2009 Lincoln MKS speed sensor
Replies: 1
Views: 32

Re: 2009 Lincoln MKS speed sensor

It would be easier to tell her not to tailgate.
by Juice
Fri Jan 03, 2020 8:31 pm
Forum: Configuration and Programming
Topic: 2011 F150 5.0 SC new PCM
Replies: 17
Views: 434

Re: 2011 F150 5.0 SC new PCM

I have done the PATS programming on my mustang. You have to perform an initialization before you can program the keys. You said you have 2 new keys. Why? There should be no reason you couldnt use your old keys. You may need to delete any existing keys to program new ones, even if you are reusing the...
by Juice
Mon Dec 30, 2019 9:57 pm
Forum: Configuration and Programming
Topic: Speedometer Calibration 99 F150
Replies: 1
Views: 88

Re: Speedometer Calibration 99 F150

Your truck probably does not have an ms can. You have two options: pay the dealer to correct tire size as long as your tires are not bigger than the maximum size setting allowed. Second option is to get a tuner device. The settings you are after are PCM programmable parameters. (Gear ratio, final dr...
by Juice
Sun Dec 29, 2019 1:27 pm
Forum: General and Support forum
Topic: Issue found with latest beta
Replies: 0
Views: 90

Issue found with latest beta

On my 2013 mustang, the PCM VID block programming does not work anymore. It was working with the last version. The function starts, but never displays anything. (Blank page) As-built PCM programming is there.
I rolled Forscan back to earlier version and I was able to change tire size.
by Juice
Fri Dec 27, 2019 12:08 pm
Forum: Configuration and Programming
Topic: 08 Ford Mustang Bcm reprogramming
Replies: 3
Views: 153

Re: 08 Ford Mustang Bcm reprogramming

Did you actually install the SJB (bcm) from the donor? You may be able to program the cluster itself and turn those warning lights off there. I upgraded my cluster and was able to turn off the ABS and Traction control lights in the cluster. (I dont have abs) how did you turn those off? Experimented...