Search found 9 matches

by andresmorago
Tue Jul 11, 2017 1:59 am
Forum: General and Support forum
Topic: Focus 4" to 8" screen upgrade-help with active parking lines
Replies: 5
Views: 4262

Re: Focus 4" to 8" screen upgrade-help with active parking l

I ended up fixing this damn issue by performing a master reset from the apim menu. That simple it was :roll:
A forscan module reset couldn't fix the issue.
by andresmorago
Mon Jul 10, 2017 4:40 pm
Forum: General and Support forum
Topic: 2014 Edge Limited (DIY Picklock)
Replies: 5
Views: 5593

Re: 2014 Edge Limited (DIY Picklock)

7D0-02-01 **** XXXX XXXX

5753 allows NAV in motion on Sync2 only but Sirius Travel Link no longer works
by andresmorago
Mon Jul 10, 2017 1:36 pm
Forum: General and Support forum
Topic: Focus 4" to 8" screen upgrade-help with active parking lines
Replies: 5
Views: 4262

Re: Focus 4" to 8" screen upgrade-help with active parking l

hello again i made some progress recently. I have no DTC's when i run forscan diagnostics and bluetooth audio now works well. Issue is with parking aids. Especifically the active parking lines: -camera video goes to the screen and shows nicely -sound feedback is OK -car drawing with obstacle detecti...
by andresmorago
Wed Jul 05, 2017 3:39 am
Forum: Diagnostics and Maintenance using FORScan
Topic: Forscan CAN-BUS Global test
Replies: 6
Views: 9280

Re: Forscan CAN-BUS Global test

This would be very cool actually. In my case, I just added a sync2 apim and needed to wire ms-can to it. I'm not 100% percent sure if network is recognizing the new unit.
by andresmorago
Fri Jun 30, 2017 3:00 am
Forum: Diagnostics and Maintenance using FORScan
Topic: Need to reprogram rear camera
Replies: 24
Views: 27237

Re: Need to reprogram rear camera

I was able to represent my issue with the parking lines. I can see them working only for 5 seconds and just right after rebooting the apim. After that, active lines will disappear https://youtu.be/qbMgNHXNsT8 Edit: I ended up fixing this damn issue by performing a master reset from the apim menu. Th...
by andresmorago
Tue Jun 20, 2017 11:57 pm
Forum: General and Support forum
Topic: Focus 4" to 8" screen upgrade-help with active parking lines
Replies: 5
Views: 4262

Re: Focus 4 inch to 8 inch screen upgrade - help with APIM d

hello again some progress.... *i disabled DSP module from the APIM. This corrected the issues related with not being able to change treble/bass - front/rear - speed compensated volume settings! Make sure this byte is set to 2 APIM 7D0-01-01 2 A21 9001 E2EF *I was able to enable the parking aids by m...
by andresmorago
Tue Jun 20, 2017 11:53 pm
Forum: Diagnostics and Maintenance using FORScan
Topic: Need to reprogram rear camera
Replies: 24
Views: 27237

Re: Need to reprogram rear camera

Hello again I was able to enable the parking aids by modifying the APIM ab data: 7D0-01-01  2 A 21  9001 E2EF  Now i get a small car drawing on the right top area of the screen with the 4 parking sensors. :mrgreen: Im still struggling on the parking active lines. After modifying the byte shown above...
by andresmorago
Tue Jun 20, 2017 5:40 pm
Forum: General and Support forum
Topic: Focus 4" to 8" screen upgrade-help with active parking lines
Replies: 5
Views: 4262

Focus 4" to 8" screen upgrade-help with active parking lines

Hello I just finished the upgrade from a non-touch Sync unit (4 inch screen) to a Myford Touch 8 inch screen on my 2015 Focus SE. The built wire harness has worked ok as the screen boots and functions relatively ok. I did some changes using foCCCus hoping that this would help me with the configurati...
by andresmorago
Tue Jun 20, 2017 3:02 pm
Forum: Diagnostics and Maintenance using FORScan
Topic: Need to reprogram rear camera
Replies: 24
Views: 27237

Re: Need to reprogram rear camera

Hello to all i would like to consult if theres any way to reprogram my camera on a 2015 Focus SE. I just installed a SYNC2 APIM and im having the following issues: *Video is OK *Parking lines wont move according to steering wheel *Parking aids (color blocks) wont show at all Im running version 2.3.8...