Search found 76 matches

by sheltonfilms
Wed Aug 29, 2018 12:33 am
Forum: Diagnostics and Maintenance using FORScan
Topic: Mustang idle issues, KAM memory fault
Replies: 4
Views: 435

Re: Mustang idle issues, KAM memory fault

F2.21 is the fuse that is "Hot at all times" for the PCM. It's 5 amps and is in the Central Junction Box. If this fuse is good make sure there is power to it. If all this checks out then go to the PCM connector and check for voltage on pin 55 (Red wire with white stripe). It's straight battery volta...
by sheltonfilms
Fri Mar 09, 2018 2:45 am
Forum: Diagnostics and Maintenance using FORScan
Topic: 2006 Explorer with Powertrain Malfunction Indicator
Replies: 12
Views: 2797

Re: 2006 Explorer with Powertrain Malfunction Indicator

Ok so that's good. Means both keys work. That line again has me concerned. I really don't think it would cause an issue with the keys unless the VIN portion is tampered with. Good thing is you have both keys and forscan can reprogram them if something happens during the process. I can send the Forsc...
by sheltonfilms
Fri Mar 09, 2018 2:35 am
Forum: Diagnostics and Maintenance using FORScan
Topic: 2006 Explorer with Powertrain Malfunction Indicator
Replies: 12
Views: 2797

Re: 2006 Explorer with Powertrain Malfunction Indicator

Should but there is a line I'm seeing in the service manual that concerns me (hold off for right now until you can answer the questions below): NOTE NOTE: If the IC is installed new, updated, or re-configured, the IC requires a parameter reset to allow the IC and the PCM to recognize the Passive Ant...
by sheltonfilms
Fri Mar 09, 2018 2:18 am
Forum: Diagnostics and Maintenance using FORScan
Topic: 2006 Explorer with Powertrain Malfunction Indicator
Replies: 12
Views: 2797

Re: 2006 Explorer with Powertrain Malfunction Indicator

One of those bytes is for 4x4 and the other is for rear parking sensors. I checked your VIN and see you didn't have it but the IC cluster's VIN does. This should also clear the code below because it's currently trying to communicate with a module that isn't there. IC U0159 -60 lost communication wit...
by sheltonfilms
Fri Mar 09, 2018 2:15 am
Forum: Diagnostics and Maintenance using FORScan
Topic: 2006 Explorer with Powertrain Malfunction Indicator
Replies: 12
Views: 2797

Re: 2006 Explorer with Powertrain Malfunction Indicator

Ok I compared your AS BUilt to what ford factory programmed your vehicle to. The instrument cluster you got was from VIN 1FMEU73E66UA12726 (720-02-1 though 720-06-01 is the hexadecimal equivalent of the vin number). The first line (720-01-01) in your picture is 99 07 69 D0 02 and it should be 99 05 ...
by sheltonfilms
Thu Mar 08, 2018 11:56 pm
Forum: Diagnostics and Maintenance using FORScan
Topic: 2006 Explorer with Powertrain Malfunction Indicator
Replies: 12
Views: 2797

Re: 2006 Explorer with Powertrain Malfunction Indicator

Don't worry about the monitors. You got code p1000 because the keep alive memory was wiped out from a battery disconnect. Was the instrument cluster brand new or was it programmed to another vehicle? The shop probably just did a parameter reset so they could program the PATS system. Sounds like the ...
by sheltonfilms
Thu Mar 08, 2018 5:31 am
Forum: Configuration and Programming
Topic: Can't seem to add second key
Replies: 1
Views: 652

Re: Can't seem to add second key

Have you tried programming the 2nd key first to see if that is successful?
by sheltonfilms
Thu Mar 08, 2018 5:25 am
Forum: Diagnostics and Maintenance using FORScan
Topic: 2006 Explorer with Powertrain Malfunction Indicator
Replies: 12
Views: 2797

Re: 2006 Explorer with Powertrain Malfunction Indicator

The powertrain malfunction light is just an extension of the check engine light. It means the PCM has caught something going on or the 4x4 module has (if equipped) and a code has been set. This code may or may not be picked up by generic scanners but forscan should pull it for you. Also since versio...
by sheltonfilms
Thu Mar 08, 2018 5:11 am
Forum: Diagnostics and Maintenance using FORScan
Topic: Steering Wheel Angle module / address?
Replies: 2
Views: 854

Re: Steering Wheel Angle module / address?

Look at the SCCM and see if you see a PID for it.
by sheltonfilms
Sat Nov 18, 2017 5:43 am
Forum: Configuration and Programming
Topic: Important notes about As Built configuration and programming
Replies: 15
Views: 28788

Re: Important notes about As Built configuration and program

Who found #1? Has this been confirmed on multiple vehicles, or is it currently a one time occurrence?