Search found 49 matches

by semiho
Mon Jul 08, 2019 9:32 am
Forum: Configuration and Programming
Topic: Sync 2 help to enable park pilot display
Replies: 10
Views: 867

Re: Sync 2 help to enable park pilot display

how did you resolve the chimes issue? Depending to your PDC system there are suitable as-built configurations in both APIM and ACM. As, Mark already told, focus mk3 (pre-lift) uses C1MCA Architecture while face-lift focus M(k3.5) uses the CGEA 1.3. Same applies to C-Max and Kuga pre-lift and faceli...
by semiho
Tue Jun 25, 2019 8:04 pm
Forum: Configuration and Programming
Topic: Focus MK4 no APIM Module visible
Replies: 6
Views: 471

Re: Focus MK4 no APIM Module visible

davetcollection wrote:
Fri Jun 21, 2019 8:26 am
Hi, can you tell me what version of Forscan you are using and what lead you are using please?
I guess it it was 2.3.21 and elm327.
by semiho
Thu Jun 20, 2019 2:56 pm
Forum: Configuration and Programming
Topic: Focus MK4 no APIM Module visible
Replies: 6
Views: 471

Re: Focus MK4 no APIM Module visible

I've configured my car APIM without any problem. Are you sure you have SYNC3? Because mk4 has both SYNC 3 and lite version of it which is called SYNC. I don't know if it could be programmed.
by semiho
Tue Apr 02, 2019 8:11 pm
Forum: Configuration and Programming
Topic: EU Fiesta Mk7.5 - Reverse Sensor Retrofit
Replies: 5
Views: 757

Re: EU Fiesta Mk7.5 - Reverse Sensor Retrofit

You should also need to configure FCDIM (for Sync 1) or APIM (for Sync 2 or higher) to show parking sensors info.
by semiho
Tue Apr 02, 2019 8:00 pm
Forum: Configuration and Programming
Topic: Information center display 2017 Focus ST
Replies: 1
Views: 287

Re: Information center display 2017 Focus ST

hate the headlights staying on and find myself waiting till they turn off before leaving the car) Just for the info. You can turn off delayed headlamps manually by pulling signal switch (like flashing headlights) just before leaving the car. I'm also wondering about Focus IPC as built data but can'...
by semiho
Wed Mar 27, 2019 12:59 pm
Forum: Configuration and Programming
Topic: Kuga sync 2 retrofit
Replies: 53
Views: 2372

Re: Kuga sync 2 retrofit

You are most welcome. Happy to hear that! :)
by semiho
Tue Mar 26, 2019 10:33 pm
Forum: Configuration and Programming
Topic: Kuga sync 2 retrofit
Replies: 53
Views: 2372

Re: Kuga sync 2 retrofit

Can you try this

7D0-01-01 x9xx xxxx xxxx
by semiho
Tue Mar 26, 2019 6:07 am
Forum: Configuration and Programming
Topic: Kuga sync 2 retrofit
Replies: 53
Views: 2372

Re: Kuga sync 2 retrofit

We forgot about that. Well done friends :)
by semiho
Mon Mar 25, 2019 8:22 am
Forum: Configuration and Programming
Topic: Kuga sync 2 retrofit
Replies: 53
Views: 2372

Re: Kuga sync 2 retrofit

I guess you applied as-built which is sent by Mark. This VIN is belongs to a European Kuga with automated parking. Please set the following lines as I stated.

PDC Architecture to CIMCA
7D0-02-02 - xxxx 2xxxx xx

Rear parking assist only.
7D0-04-02 - xxx1
by semiho
Mon Mar 25, 2019 7:32 am
Forum: Configuration and Programming
Topic: Kuga sync 2 retrofit
Replies: 53
Views: 2372

Re: Kuga sync 2 retrofit

andspenka wrote:
Sun Mar 24, 2019 9:37 pm
Thanks Mark, that's great.

Yes I get the beeps but nothing on the display, in fact it doesn't even change from the home screen.
You have only rear parking sensors without backup camera if understand correct. Can you share your APIM and PAM as-built so I can take a look.