Search found 33 matches

by tractmec
Tue Nov 05, 2019 5:53 am
Forum: Diagnostics and Maintenance using FORScan
Topic: Ford Explorer 2003 Modules Missing
Replies: 9
Views: 4657

Re: Ford Explorer 2003 Modules Missing

Forscan has UBP support as of version 2.3.09 but only for Ford VCM2 Adapters and VCM2 Clones. I helped to develop it during 2.3.09beta with my 03 Expedition and 05 F150 and a High quality Clone. Support for UBP protocols in ELM327 based adapters is still being worked on hence the prompt for the swit...
by tractmec
Wed Oct 30, 2019 9:32 pm
Forum: Diagnostics and Maintenance using FORScan
Topic: 2010 Fusion Puddle Lamps not working + looking for spreadsheet
Replies: 1
Views: 123

Re: 2010 Fusion Puddle Lamps not working + looking for spreadsheet

Hello bandrews8 Brandon You could try this (https://drive.google.com/open?id=0Bw7jDvlqxa5UeXZQU3lfb0luQ1E). It's called Asbuilt hacker and I have used it on my wifes 2010 Fusion SLE AWD to find options and the correct configuration for the PSCM module when I replaced the electronic power steering un...
by tractmec
Sun Oct 27, 2019 10:15 pm
Forum: Configuration and Programming
Topic: Fusion 2012 tire pressure warning light
Replies: 3
Views: 181

Re: Fusion 2012 tire pressure warning light

Hello Turassi My wifes 2010 Fusion SEL AWD has this located in the Body control module (BCM). Address 726-08-01 0005 02 3D Disables TPMS, 726-08-01 0105 02 3E will enable TPMS and is set to this code and enabled in the wife's 2010. The last two digits are check sums and should calculate automaticall...
by tractmec
Thu Oct 24, 2019 5:52 pm
Forum: General and Support forum
Topic: HS / MS SWITCH
Replies: 3
Views: 267

Re: HS / MS SWITCH

Hello avic I am not familiar with the Transits, if that is the vehicle you are asking about? If it is anything like my 2005 F150 it will not have any MSCAN modules and if Forscan does not expect any or see a connection to any MSCAN/UBP modules, it won't ask for the switch to be changed. My ELMSCAN5 ...
by tractmec
Mon Oct 14, 2019 4:44 am
Forum: General and Support forum
Topic: Historic DTC codes
Replies: 4
Views: 260

Re: Historic DTC codes

Hi rich That first code you list P2831(Shift Fork Position A Circuit Fault) is TCM(Transmission Control Module) code that can get set when there is a low or high voltage problem. The first Pin Point test for this code asks for a complete check of all modules for any voltage codes. The other two code...
by tractmec
Mon Oct 14, 2019 3:48 am
Forum: Adapters & Connection
Topic: Red X over VCM, Forscan hangs
Replies: 3
Views: 540

Re: Red X over VCM, Forscan hangs

Hello thatguy Check in your program files for the VCI manager in the Bosch program folder and double click it to open it. A manager should load with an icon of your VCM with its Serial Number underneath and two buttons at the bottom marked connect and disconnect and if the VCM is detected the connec...
by tractmec
Wed Oct 09, 2019 4:14 am
Forum: General and Support forum
Topic: Enabling Modules to work...
Replies: 3
Views: 262

Re: Enabling Modules to work...

Hello I would not be so quick to condemn the PCM, as a battery nearing the end of its usefulness will cause voltage DTC's to set in many modules if voltage drops below 11 volts particularly during starting and this can happen with a poor battery condition and still start like normal. A failing alter...
by tractmec
Tue Oct 08, 2019 9:58 pm
Forum: General and Support forum
Topic: Enabling Modules to work...
Replies: 3
Views: 262

Re: Enabling Modules to work...

Hello 5280: I have this same Expy and that configuration will be in the VSM(vech security module) if it was equipped with it and quite likely is. Check for a code number on a module(VSM) high up in the passenger foot well. Should look like this 77451(what a previous totaled 03 Expy I owned had as it...
by tractmec
Tue Sep 17, 2019 2:25 am
Forum: General and Support forum
Topic: ms-can vs scp
Replies: 11
Views: 350

Re: ms-can vs scp

Hi Phnorris If it is anything like the 03 Expy, the IPC will show as connected to the same network as the PCM as the PCM is where the odometer/speedometer data is collected and is stored. In my expy that is on the SPC/PWM Network and in your case it appears to be HSCan. Other functions are likely mo...
by tractmec
Fri Sep 13, 2019 11:47 pm
Forum: Adapters & Connection
Topic: 2008 F150 ISO/UBP MODULES
Replies: 7
Views: 569

Re: 2008 F150 ISO/UBP MODULES

Hi SIGNAL20K9 I will have to correct my self as I am an old man and my fingers get on the wrong keys and my memory is not as good as it used to be! The model number should be "SP177-C or C1"(has wireless capability) but unfortunately they seem to be out of stock where I bought my mine at http://www....