How to use Output Control mode in FORScan 2.2.*

Share your FORScan experience with other users

How to use Output Control mode in FORScan 2.2.*

Postby FORScan » Sat Jan 10, 2015 8:06 am

Output Control mode is special mode to substitute output signals to actuators, normally generated by a module, with the ones specified by operator. Or, in other words, temporarily transfers the actuators control from ECU to operatior. This mode is possible only when the module is switched to a special diagnostic mode. The mode limits normal module operations, so, for example, the instrument cluster in this mode may not not show anything. And if PCM is in the diagnostic mode and operator tries to drive, the engine will most likely stall (and this is not a FORScan limitation, but the control module limitation). We strongly recommend to use the Output Control function only when the vehicle is parked.

So, the only objective of the Output Control function is a diagnostic one. For example, using this function it is easy to check if the cooling fan normally works on low and high speed, or a lamp in the instrument cluster really works. It should be noted, however, that the Output Control may be implemented not for all actuators.

Let's review a use case for the following scenario: user wants to check instrument cluster lamps and gauges on Ford Ecosport 2014.

- Run FORScan, connect to vehicle, go to the Dashboard section, click Setup All Gauges button (or double click on a gauge). In the PIDs selection dialog, select the Control type:

OSC1.png
OSC1.png (54.55 KiB) Viewed 41684 times


Also select some read PIDs.

- Press the Control button:

OSC2.png
OSC2.png (52.2 KiB) Viewed 41684 times


The Output Control window will open:

OSC3.png
OSC3.png (67.62 KiB) Viewed 41684 times


Change its size and position to a convenient onee.

The function can be activated only when the Live Streaming is started. So for now all the controls in the Output Control windows are disabled.

At this moment there are 2 types of the Output controls: buttons are used for state parameters, such as On Off (there can be multiple states) and sliders are used for analogue parameters.

- Run the live streaming by pressing Start button. The output controls become activated and ready to use.

- Activate a control

Important note: current version of FORScan implements the following Output Control management logic: when the live streaming is started, the Output Control mode is not really activated. PIDs are read as usually in the live streaming mode. However, as soon as a control is activated for the first time, FORScan switches the model to the output control mode. PIDs continue to be read, however, their performance may suffer (especially when a control is touched). It should be noted that the management is transferred for the only actuator that was touched. Other actuators still managed by the module. If operator touches a second control, the corresponding actuator's management will be transferred to operator. And so on. There is no possibility to transfer the control back to the moduile for a specific actuator. The only way to switch back from the output control mode to the normal mode is to close the Output Control window.

Important note: FORScan doesn't care about seamless switching from one mode to another. So, in our example, if IC illumination in normal mode is 80% and user has set it to 0%, the IC display will shut the illumination off. In this example it is safe, however in some cases, for example when you manage a powertrain actuator, such as spark advance or somethink like this, it may be not unsafe. Another thing is a control of minimum and maximum value parameter, it is not performed as well (normally, it should be managed by module itself, but we recommend to be very careful anyway).

This is how the Output control window should look like when used:

OSC4.png
OSC4.png (25.77 KiB) Viewed 41684 times


- If the control doesn't respond as expected, the common log should be checked. Every Output Control operation is logged here, either as successful or as error:

OSC5.png
OSC5.png (76.1 KiB) Viewed 41684 times


Normally, there should be no errors. If you experience one, you need to contact us and send internal FORScan logs from this vehicle. If there is no error, but the actuator still doesn't respond or responds not like expected, it most likely means the module supports this command but doesn't really serve it. However, FORScan bug is not fully exluded too.
FORScan
Site Admin
 
Posts: 2476
Joined: Fri Jun 13, 2014 2:21 am

Re: How to use Output Control mode in FORScan 2.2.*

Postby ivifocus » Tue Jul 12, 2016 5:19 am

Hi All!
I have an 2006 S-Max Mk1 1.8tdci (Lynx), and I cannot enable autolock function. I get the "error changing PID". Where is the problem? Thanks!
ivifocus
 
Posts: 1
Joined: Wed Jul 06, 2016 8:48 pm
Vehicle: Ford S-Max 1.8 tdci 125HPS 2006

Re: How to use Output Control mode in FORScan 2.2.*

Postby misk » Sun Sep 18, 2016 12:59 pm

could this be used to activate air conditioning through the pcm when an engine conversion is done? there is no icc but the pcm controls the actual operation of the ac system. without the icc there is no way to trigger the setup so it runs through the pcm rather than using external switches etc
misk
 
Posts: 4
Joined: Mon Sep 12, 2016 10:05 am
Vehicle: fg ex taxi

Re: How to use Output Control mode in FORScan 2.2.*

Postby bogdaniova » Tue Jan 17, 2017 9:20 pm

Hi,
can i change the tipe of transmision in PCM? I change the transmission from cvt to mechanical and the car can get more the 85km/h.
bogdaniova
 
Posts: 3
Joined: Fri Apr 15, 2016 7:31 am
Location: Romania
Vehicle: ford ka, 2001, 44

Re: How to use Output Control mode in FORScan 2.2.*

Postby Wayne » Mon Apr 24, 2017 7:09 am

I am using 2.3.7 beta
On a ford Focus mk 1.5 , 1.8 liter I do not see any option to control the Low And high Speed Cooling Fan under the PCM ? for Diagnostics
Wayne
 
Posts: 6
Joined: Wed Jul 27, 2016 8:02 am
Vehicle: Focus Mk1.5 1.8L Petrol 2002 Australia

Re: How to use Output Control mode in FORScan 2.2.*

Postby monta990 » Wed Aug 02, 2017 5:10 am

Wayne wrote:I am using 2.3.7 beta
On a ford Focus mk 1.5 , 1.8 liter I do not see any option to control the Low And high Speed Cooling Fan under the PCM ? for Diagnostics


Me too, i have a ford focus mk 1.5 (2006 from Argentina Plant) PCM model 6S45CA, and i not see the control of hight and low fan speed
monta990
 
Posts: 1
Joined: Tue Jun 09, 2015 8:19 pm
Vehicle: Focus 2006 2.0l Duratec 16v


Return to Diagnostics and Maintenance using FORScan

Who is online

Users browsing this forum: No registered users and 5 guests