FORScan release notes

Any issues related to FORScan application

Re: FORScan release notes

Postby lollapalooza » Thu Oct 13, 2016 4:25 pm

DeclanJewell wrote:Can anybody help me here in accessing the config files?
Cheers in advance

Your question is already answered. Just read a few messages above yours.
Posts: 49
Joined: Wed Feb 24, 2016 3:57 pm
Vehicle: Ford Fiesta 1.6 TDCi 2011

Re: FORScan release notes

Postby MarcoGaspar » Fri Nov 18, 2016 8:58 pm


Trying to use Central Configuration on Mondeo 1.8 TDCI 2008 but getting error:

(OK) [21:08:58.283] Central configuration (Main) has been started
(WARN) [21:08:58.317] Read configuration from primary module...
(WARN) [21:09:07.022] Loading SBL to primary module...
(WARN) [21:09:07.305] Loading block 1/4...
(WARN) [21:09:27.596] Loading block 2/4...
(WARN) [21:09:27.981] Loading block 3/4...
(WARN) [21:09:28.325] Loading block 4/4...
(OK) [21:09:28.892] SBL loaded successfully
(OK) [21:09:29.137] Read block #1
(OK) [21:09:29.288] Read block #2
(OK) [21:09:30.009] Read block #3
(OK) [21:09:30.127] Read block #4
(ERR) [21:09:31.395] Reading block 5 failed
(ERR) [21:09:31.418] Service procedure has been interrupted

Whats the problem?

Best Regards,
Marco Gaspar
Posts: 9
Joined: Tue Feb 23, 2016 9:39 pm
Vehicle: Ford Mondeo, 1.8tdci, 2008

Re: FORScan release notes

Postby Yoko89 » Wed Mar 08, 2017 11:39 am

rioachim wrote:

I can't find calibration files for the cars i want
Posts: 5
Joined: Sun Jan 01, 2017 4:48 pm
Vehicle: Fiesta 1.6 105hp 2014

FORScan release notes v2.3.8

Postby FORScan » Tue Mar 28, 2017 6:46 am

Version 2.3.8 has 2 quite important functions added:

1. Built-in outcode-incode generator for pre-2011 vehicles with coded PATS. Now it is not necessary to use an outside outcode-incode generator that was often inconvenient. Corresponding article is updated: viewtopic.php?f=6&t=839

2. Ability to read parameters (PIDs) from several modules simultaneously. New article is created to explain it: viewtopic.php?f=6&t=3334
Site Admin
Posts: 2417
Joined: Fri Jun 13, 2014 2:21 am

Re: FORScan release notes

Postby cckst » Tue Apr 11, 2017 12:01 pm

Hi, may I have ask question about the new version.
When the new version support Mazda year 2017 model?
Today I had try to connect Forscan 2.3.8 to Mazda Demio 2017. But There is pop up window which talking about unknow PCM.
This version is working fine in model 2014-2016. Kindly advise. Thank you
Posts: 1
Joined: Fri Jul 01, 2016 1:05 pm
Vehicle: Mazda DEMIO 2016

Re: FORScan release notes

Postby bizkitt » Tue Apr 11, 2017 8:58 pm

Same exact issue as MarcoGaspar... Reading block 5 failed on a 07 Mondeo 2.0 TDCI, guys correct me if i`m wrong... do you need to load SBL to read the CCF form BCM? i dont think so.. you can read it by pid just send "22F105" read 512bytes from "0x00FF8000 to 0x00FF81FF" than after editing before sending it back divide it into the 5 blocks like :

1st block 0x00FF8000 to 0x00FF8057
2nd ........
3rd ........
4th ........
5th ........
proceed and send it back to BCM like:
1000x of 10 82`s :D + 27 01 Pass security, load SBL + activate it, erase + flash blocks and end it with a reset 11 81...
if the right person sees what i wrote here will PM me i might be able to help...
Posts: 6
Joined: Fri Apr 07, 2017 10:38 pm
Vehicle: Mondeo MK4, 2.0 TDCI, 138hp, 2007


Return to General and Support forum

Who is online

Users browsing this forum: No registered users and 6 guests